Split subproject make files into Makefile and rules.mk

example_keyboards
Fred Sundvik 8 years ago
parent c83af54513
commit 051017c312

@ -1,41 +1,3 @@
# project specific files
SRC = matrix.c \
led.c
## chip/board settings
# the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F0xx
# linker script to use
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
MCU_LDSCRIPT = STM32F072xB
# startup code to use
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP = stm32f0xx
# it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
BOARD = ST_STM32F072B_DISCOVERY
# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU = cortex-m0
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
# a custom board definition that you plan to reuse).
# If you're not setting it here, leave it commented out.
# It is chip dependent, the correct number can be looked up here (page 175):
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
# This also requires a patch to chibios:
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
# Build Options
# comment out to disable the options.
#
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,41 @@
# project specific files
SRC = matrix.c \
led.c
## chip/board settings
# the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F0xx
# linker script to use
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
MCU_LDSCRIPT = STM32F072xB
# startup code to use
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP = stm32f0xx
# it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
BOARD = ST_STM32F072B_DISCOVERY
# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU = cortex-m0
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 6
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
# a custom board definition that you plan to reuse).
# If you're not setting it here, leave it commented out.
# It is chip dependent, the correct number can be looked up here (page 175):
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
# This also requires a patch to chibios:
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
# Build Options
# comment out to disable the options.
#
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,52 +1,3 @@
# project specific files
SRC = matrix.c \
led.c
# GENERIC STM32F103C8T6 board - stm32duino bootloader
OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
BOARD = GENERIC_STM32_F103
# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD)
# OPT_DEFS =
# MCU_LDSCRIPT = STM32F103x8
# BOARD = GENERIC_STM32_F103
# MAPLE MINI
# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000
# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader
# BOARD = MAPLEMINI_STM32_F103
## chip/board settings
# the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F1xx
# linker script to use
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# startup code to use
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP = stm32f1xx
# it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU = cortex-m3
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
# a custom board definition that you plan to reuse).
# If you're not setting it here, leave it commented out.
# It is chip dependent, the correct number can be looked up here (page 175):
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
# This also requires a patch to chibios:
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,52 @@
# project specific files
SRC = matrix.c \
led.c
# GENERIC STM32F103C8T6 board - stm32duino bootloader
OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
BOARD = GENERIC_STM32_F103
# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD)
# OPT_DEFS =
# MCU_LDSCRIPT = STM32F103x8
# BOARD = GENERIC_STM32_F103
# MAPLE MINI
# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000
# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader
# BOARD = MAPLEMINI_STM32_F103
## chip/board settings
# the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
MCU_FAMILY = STM32
MCU_SERIES = STM32F1xx
# linker script to use
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# startup code to use
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
MCU_STARTUP = stm32f1xx
# it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU = cortex-m3
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
ARMV = 7
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
# a custom board definition that you plan to reuse).
# If you're not setting it here, leave it commented out.
# It is chip dependent, the correct number can be looked up here (page 175):
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
# This also requires a patch to chibios:
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,49 +1,3 @@
# project specific files
SRC = matrix.c \
led.c
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
# - For Teensies, FAMILY = KINETIS and SERIES is either
# KL2x (LC) or K20x (3.0,3.1,3.2).
MCU_FAMILY = KINETIS
MCU_SERIES = KL2x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
# - LDSCRIPT =
# - MKL26Z64 for Teensy LC
# - MK20DX128 for Teensy 3.0
# - MK20DX256 for Teensy 3.1 and 3.2
MCU_LDSCRIPT = MKL26Z64
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
# - STARTUP =
# - kl2x for Teensy LC
# - k20x5 for Teensy 3.0
# - k20x7 for Teensy 3.1 and 3.2
MCU_STARTUP = kl2x
# Board: it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# - BOARD =
# - PJRC_TEENSY_LC for Teensy LC
# - PJRC_TEENSY_3 for Teensy 3.0
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
BOARD = PJRC_TEENSY_LC
# Cortex version
# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4
MCU = cortex-m0plus
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
ARMV = 6
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif

@ -0,0 +1,49 @@
# project specific files
SRC = matrix.c \
led.c
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
# - For Teensies, FAMILY = KINETIS and SERIES is either
# KL2x (LC) or K20x (3.0,3.1,3.2).
MCU_FAMILY = KINETIS
MCU_SERIES = KL2x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
# - LDSCRIPT =
# - MKL26Z64 for Teensy LC
# - MK20DX128 for Teensy 3.0
# - MK20DX256 for Teensy 3.1 and 3.2
MCU_LDSCRIPT = MKL26Z64
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
# - STARTUP =
# - kl2x for Teensy LC
# - k20x5 for Teensy 3.0
# - k20x7 for Teensy 3.1 and 3.2
MCU_STARTUP = kl2x
# Board: it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# - BOARD =
# - PJRC_TEENSY_LC for Teensy LC
# - PJRC_TEENSY_3 for Teensy 3.0
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
BOARD = PJRC_TEENSY_LC
# Cortex version
# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4
MCU = cortex-m0plus
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
ARMV = 6
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,5 +1,3 @@
BACKLIGHT_ENABLE = no
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,5 @@
BACKLIGHT_ENABLE = no
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,5 +1,3 @@
BACKLIGHT_ENABLE = yes
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,5 @@
BACKLIGHT_ENABLE = yes
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,76 +1,3 @@
#----------------------------------------------------------------------------
# On command line:
#
# make = Make software.
#
# make clean = Clean out built project files.
#
# That's pretty much all you need. To compile, always go make clean,
# followed by make.
#
# For advanced users only:
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
#----------------------------------------------------------------------------
# # project specific files
SRC = twimaster.c \
matrix.c
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# comment out to disable the options.
#
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,76 @@
#----------------------------------------------------------------------------
# On command line:
#
# make = Make software.
#
# make clean = Clean out built project files.
#
# That's pretty much all you need. To compile, always go make clean,
# followed by make.
#
# For advanced users only:
# make teensy = Download the hex file to the device, using teensy_loader_cli.
# (must have teensy_loader_cli installed).
#
#----------------------------------------------------------------------------
# # project specific files
SRC = twimaster.c \
matrix.c
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# comment out to disable the options.
#
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,77 +1,3 @@
# project specific files
SRC = matrix.c \
led.c
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
# - For Teensies, FAMILY = KINETIS and SERIES is either
# KL2x (LC) or K20x (3.0,3.1,3.2).
# - For Infinity KB, SERIES = K20x
MCU_FAMILY = KINETIS
MCU_SERIES = K20x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
# - LDSCRIPT =
# - MKL26Z64 for Teensy LC
# - MK20DX128 for Teensy 3.0
# - MK20DX256 for Teensy 3.1 and 3.2
# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader
# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader
MCU_LDSCRIPT = MK20DX256BLDR8
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
# - STARTUP =
# - kl2x for Teensy LC
# - k20x5 for Teensy 3.0 and Infinity 60%
# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox
MCU_STARTUP = k20x7
# Board: it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# - BOARD =
# - PJRC_TEENSY_LC for Teensy LC
# - PJRC_TEENSY_3 for Teensy 3.0
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
# - MCHCK_K20 for Infinity KB
#BOARD = MCHCK_K20
BOARD = PJRC_TEENSY_3_1
# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
ARMV = 7
# Vector table for application
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000
# Build Options
# comment out to disable the options.
#
CUSTOM_MATRIX ?= yes # Custom matrix file
SERIAL_LINK_ENABLE = yes
VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile
LCD_ENABLE ?= yes
LED_ENABLE ?= yes
LCD_BACKLIGHT_ENABLE ?= yes
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
ifdef LCD_ENABLE
include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk
endif
ifdef LED_ENABLE
include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk
endif
endif

@ -0,0 +1,77 @@
# project specific files
SRC = matrix.c \
led.c
## chip/board settings
# - the next two should match the directories in
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
# - For Teensies, FAMILY = KINETIS and SERIES is either
# KL2x (LC) or K20x (3.0,3.1,3.2).
# - For Infinity KB, SERIES = K20x
MCU_FAMILY = KINETIS
MCU_SERIES = K20x
# Linker script to use
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
# or <this_dir>/ld/
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
# - LDSCRIPT =
# - MKL26Z64 for Teensy LC
# - MK20DX128 for Teensy 3.0
# - MK20DX256 for Teensy 3.1 and 3.2
# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader
# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader
MCU_LDSCRIPT = MK20DX256BLDR8
# Startup code to use
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
# - STARTUP =
# - kl2x for Teensy LC
# - k20x5 for Teensy 3.0 and Infinity 60%
# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox
MCU_STARTUP = k20x7
# Board: it should exist either in <chibios>/os/hal/boards/
# or <this_dir>/boards
# - BOARD =
# - PJRC_TEENSY_LC for Teensy LC
# - PJRC_TEENSY_3 for Teensy 3.0
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
# - MCHCK_K20 for Infinity KB
#BOARD = MCHCK_K20
BOARD = PJRC_TEENSY_3_1
# Cortex version
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
MCU = cortex-m4
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
ARMV = 7
# Vector table for application
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000
# Build Options
# comment out to disable the options.
#
CUSTOM_MATRIX ?= yes # Custom matrix file
SERIAL_LINK_ENABLE = yes
VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile
LCD_ENABLE ?= yes
LED_ENABLE ?= yes
LCD_BACKLIGHT_ENABLE ?= yes
ifndef QUANTUM_DIR
include ../../../Makefile
endif
ifdef LCD_ENABLE
include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk
endif
ifdef LED_ENABLE
include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk
endif

@ -1,73 +1,3 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,73 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,73 +1,3 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
endif

@ -0,0 +1,73 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,71 +1,3 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= no # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
MIDI_ENABLE ?= no # MIDI controls
AUDIO_ENABLE ?= no # Audio output on port C6
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif

@ -0,0 +1,67 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=512
# Build Options
# change to "no" to disable the options, or define them in the Makefile in
# the appropriate keymap folder that will get included automatically
#
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= no # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
MIDI_ENABLE ?= no # MIDI controls
AUDIO_ENABLE ?= no # Audio output on port C6
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend

@ -1,3 +1,3 @@
ifndef MAKEFILE_INCLUDED
include ../../Makefile
include ../../../Makefile
endif

@ -0,0 +1,65 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= yes # Console for debug(+400)
COMMAND_ENABLE ?= yes # Commands for debug and configuration
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,89 +1,3 @@
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
# for avr upload
USB ?= /dev/cu.usbmodem1421
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
ifdef TEENSY2
OPT_DEFS += -DATREUS_TEENSY2
ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
else
OPT_DEFS += -DATREUS_ASTAR
OPT_DEFS += -DCATERINA_BOOTLOADER
ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
endif
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# MCU name
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= no # Console for debug(+400)
COMMAND_ENABLE ?= no # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
RGBLIGHT_ENABLE = yes
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif
upload: build
$(ATREUS_UPLOAD_COMMAND)
endif

@ -0,0 +1,89 @@
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
# for avr upload
USB ?= /dev/cu.usbmodem1421
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
ifdef TEENSY2
OPT_DEFS += -DATREUS_TEENSY2
ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
else
OPT_DEFS += -DATREUS_ASTAR
OPT_DEFS += -DCATERINA_BOOTLOADER
ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
endif
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# MCU name
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE ?= no # Console for debug(+400)
COMMAND_ENABLE ?= no # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE ?= no # USB Nkey Rollover
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
MIDI_ENABLE ?= no # MIDI controls
UNICODE_ENABLE ?= no # Unicode
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE ?= no # Audio output on port C6
RGBLIGHT_ENABLE = yes
ifndef QUANTUM_DIR
include ../../../Makefile
endif
upload: build
$(ATREUS_UPLOAD_COMMAND)

@ -1,5 +1,3 @@
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif

@ -0,0 +1,5 @@
AUDIO_ENABLE ?= no # Audio output on port C6
ifndef QUANTUM_DIR
include ../../../Makefile
endif

@ -1,5 +1,3 @@
AUDIO_ENABLE ?= yes # Audio output on port C6
ifndef QUANTUM_DIR
ifndef MAKEFILE_INCLUDED
include ../../../Makefile
endif

@ -0,0 +1,5 @@
AUDIO_ENABLE ?= yes # Audio output on port C6
ifndef QUANTUM_DIR
include ../../../Makefile
endif
Loading…
Cancel
Save