Split subproject make files into Makefile and rules.mk
Fred Sundvik
8 years ago
parent
c83af54513
commit
051017c312
@ -1,41 +1,3 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
## chip/board settings
|
||||
# the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
MCU_FAMILY = STM32
|
||||
MCU_SERIES = STM32F0xx
|
||||
# linker script to use
|
||||
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
MCU_LDSCRIPT = STM32F072xB
|
||||
# startup code to use
|
||||
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
MCU_STARTUP = stm32f0xx
|
||||
# it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
BOARD = ST_STM32F072B_DISCOVERY
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m0
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
ARMV = 6
|
||||
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
|
||||
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
|
||||
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
|
||||
# a custom board definition that you plan to reuse).
|
||||
# If you're not setting it here, leave it commented out.
|
||||
# It is chip dependent, the correct number can be looked up here (page 175):
|
||||
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
|
||||
# This also requires a patch to chibios:
|
||||
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
|
||||
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,41 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
## chip/board settings
|
||||
# the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
MCU_FAMILY = STM32
|
||||
MCU_SERIES = STM32F0xx
|
||||
# linker script to use
|
||||
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
MCU_LDSCRIPT = STM32F072xB
|
||||
# startup code to use
|
||||
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
MCU_STARTUP = stm32f0xx
|
||||
# it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
BOARD = ST_STM32F072B_DISCOVERY
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m0
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
ARMV = 6
|
||||
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
|
||||
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
|
||||
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
|
||||
# a custom board definition that you plan to reuse).
|
||||
# If you're not setting it here, leave it commented out.
|
||||
# It is chip dependent, the correct number can be looked up here (page 175):
|
||||
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
|
||||
# This also requires a patch to chibios:
|
||||
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
|
||||
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -1,52 +1,3 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
# GENERIC STM32F103C8T6 board - stm32duino bootloader
|
||||
OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
|
||||
MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
|
||||
BOARD = GENERIC_STM32_F103
|
||||
|
||||
# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD)
|
||||
# OPT_DEFS =
|
||||
# MCU_LDSCRIPT = STM32F103x8
|
||||
# BOARD = GENERIC_STM32_F103
|
||||
|
||||
# MAPLE MINI
|
||||
# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000
|
||||
# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader
|
||||
# BOARD = MAPLEMINI_STM32_F103
|
||||
|
||||
## chip/board settings
|
||||
# the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
MCU_FAMILY = STM32
|
||||
MCU_SERIES = STM32F1xx
|
||||
# linker script to use
|
||||
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
# startup code to use
|
||||
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
MCU_STARTUP = stm32f1xx
|
||||
# it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m3
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
ARMV = 7
|
||||
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
|
||||
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
|
||||
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
|
||||
# a custom board definition that you plan to reuse).
|
||||
# If you're not setting it here, leave it commented out.
|
||||
# It is chip dependent, the correct number can be looked up here (page 175):
|
||||
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
|
||||
# This also requires a patch to chibios:
|
||||
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
|
||||
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
|
||||
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,52 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
# GENERIC STM32F103C8T6 board - stm32duino bootloader
|
||||
OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000
|
||||
MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader
|
||||
BOARD = GENERIC_STM32_F103
|
||||
|
||||
# GENERIC STM32F103C8T6 board - no bootloader (programmer over serial or SWD)
|
||||
# OPT_DEFS =
|
||||
# MCU_LDSCRIPT = STM32F103x8
|
||||
# BOARD = GENERIC_STM32_F103
|
||||
|
||||
# MAPLE MINI
|
||||
# OPT_DEFS = -DCORTEX_VTOR_INIT=0x5000
|
||||
# MCU_LDSCRIPT = STM32F103xB_maplemini_bootloader
|
||||
# BOARD = MAPLEMINI_STM32_F103
|
||||
|
||||
## chip/board settings
|
||||
# the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
MCU_FAMILY = STM32
|
||||
MCU_SERIES = STM32F1xx
|
||||
# linker script to use
|
||||
# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
# startup code to use
|
||||
# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
MCU_STARTUP = stm32f1xx
|
||||
# it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m3
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
ARMV = 7
|
||||
# If you want to be able to jump to bootloader from firmware on STM32 MCUs,
|
||||
# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in
|
||||
# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have
|
||||
# a custom board definition that you plan to reuse).
|
||||
# If you're not setting it here, leave it commented out.
|
||||
# It is chip dependent, the correct number can be looked up here (page 175):
|
||||
# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf
|
||||
# This also requires a patch to chibios:
|
||||
# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch
|
||||
#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800
|
||||
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -1,49 +1,3 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
## chip/board settings
|
||||
# - the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
# - For Teensies, FAMILY = KINETIS and SERIES is either
|
||||
# KL2x (LC) or K20x (3.0,3.1,3.2).
|
||||
MCU_FAMILY = KINETIS
|
||||
MCU_SERIES = KL2x
|
||||
|
||||
# Linker script to use
|
||||
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
|
||||
# - LDSCRIPT =
|
||||
# - MKL26Z64 for Teensy LC
|
||||
# - MK20DX128 for Teensy 3.0
|
||||
# - MK20DX256 for Teensy 3.1 and 3.2
|
||||
MCU_LDSCRIPT = MKL26Z64
|
||||
|
||||
# Startup code to use
|
||||
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
# - STARTUP =
|
||||
# - kl2x for Teensy LC
|
||||
# - k20x5 for Teensy 3.0
|
||||
# - k20x7 for Teensy 3.1 and 3.2
|
||||
MCU_STARTUP = kl2x
|
||||
|
||||
# Board: it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
# - BOARD =
|
||||
# - PJRC_TEENSY_LC for Teensy LC
|
||||
# - PJRC_TEENSY_3 for Teensy 3.0
|
||||
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
|
||||
BOARD = PJRC_TEENSY_LC
|
||||
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m0plus
|
||||
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
|
||||
ARMV = 6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,49 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
## chip/board settings
|
||||
# - the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
# - For Teensies, FAMILY = KINETIS and SERIES is either
|
||||
# KL2x (LC) or K20x (3.0,3.1,3.2).
|
||||
MCU_FAMILY = KINETIS
|
||||
MCU_SERIES = KL2x
|
||||
|
||||
# Linker script to use
|
||||
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
|
||||
# - LDSCRIPT =
|
||||
# - MKL26Z64 for Teensy LC
|
||||
# - MK20DX128 for Teensy 3.0
|
||||
# - MK20DX256 for Teensy 3.1 and 3.2
|
||||
MCU_LDSCRIPT = MKL26Z64
|
||||
|
||||
# Startup code to use
|
||||
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
# - STARTUP =
|
||||
# - kl2x for Teensy LC
|
||||
# - k20x5 for Teensy 3.0
|
||||
# - k20x7 for Teensy 3.1 and 3.2
|
||||
MCU_STARTUP = kl2x
|
||||
|
||||
# Board: it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
# - BOARD =
|
||||
# - PJRC_TEENSY_LC for Teensy LC
|
||||
# - PJRC_TEENSY_3 for Teensy 3.0
|
||||
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
|
||||
BOARD = PJRC_TEENSY_LC
|
||||
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0plus; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m0plus
|
||||
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
|
||||
ARMV = 6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -1,5 +1,3 @@
|
||||
BACKLIGHT_ENABLE = no
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,5 @@
|
||||
BACKLIGHT_ENABLE = no
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -1,5 +1,3 @@
|
||||
BACKLIGHT_ENABLE = yes
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,5 @@
|
||||
BACKLIGHT_ENABLE = yes
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -1,76 +1,3 @@
|
||||
#----------------------------------------------------------------------------
|
||||
# On command line:
|
||||
#
|
||||
# make = Make software.
|
||||
#
|
||||
# make clean = Clean out built project files.
|
||||
#
|
||||
# That's pretty much all you need. To compile, always go make clean,
|
||||
# followed by make.
|
||||
#
|
||||
# For advanced users only:
|
||||
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
||||
# (must have teensy_loader_cli installed).
|
||||
#
|
||||
#----------------------------------------------------------------------------
|
||||
|
||||
# # project specific files
|
||||
SRC = twimaster.c \
|
||||
matrix.c
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,76 @@
|
||||
#----------------------------------------------------------------------------
|
||||
# On command line:
|
||||
#
|
||||
# make = Make software.
|
||||
#
|
||||
# make clean = Clean out built project files.
|
||||
#
|
||||
# That's pretty much all you need. To compile, always go make clean,
|
||||
# followed by make.
|
||||
#
|
||||
# For advanced users only:
|
||||
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
||||
# (must have teensy_loader_cli installed).
|
||||
#
|
||||
#----------------------------------------------------------------------------
|
||||
|
||||
# # project specific files
|
||||
SRC = twimaster.c \
|
||||
matrix.c
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,77 @@
|
||||
# project specific files
|
||||
SRC = matrix.c \
|
||||
led.c
|
||||
|
||||
## chip/board settings
|
||||
# - the next two should match the directories in
|
||||
# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES)
|
||||
# - For Teensies, FAMILY = KINETIS and SERIES is either
|
||||
# KL2x (LC) or K20x (3.0,3.1,3.2).
|
||||
# - For Infinity KB, SERIES = K20x
|
||||
MCU_FAMILY = KINETIS
|
||||
MCU_SERIES = K20x
|
||||
|
||||
# Linker script to use
|
||||
# - it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/
|
||||
# or <this_dir>/ld/
|
||||
# - NOTE: a custom ld script is needed for EEPROM on Teensy LC
|
||||
# - LDSCRIPT =
|
||||
# - MKL26Z64 for Teensy LC
|
||||
# - MK20DX128 for Teensy 3.0
|
||||
# - MK20DX256 for Teensy 3.1 and 3.2
|
||||
# - MK20DX128BLDR4 for Infinity 60% with Kiibohd bootloader
|
||||
# - MK20DX256BLDR8 for Infinity ErgoDox with Kiibohd bootloader
|
||||
MCU_LDSCRIPT = MK20DX256BLDR8
|
||||
|
||||
# Startup code to use
|
||||
# - it should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/
|
||||
# - STARTUP =
|
||||
# - kl2x for Teensy LC
|
||||
# - k20x5 for Teensy 3.0 and Infinity 60%
|
||||
# - k20x7 for Teensy 3.1, 3.2 and Infinity ErgoDox
|
||||
MCU_STARTUP = k20x7
|
||||
|
||||
# Board: it should exist either in <chibios>/os/hal/boards/
|
||||
# or <this_dir>/boards
|
||||
# - BOARD =
|
||||
# - PJRC_TEENSY_LC for Teensy LC
|
||||
# - PJRC_TEENSY_3 for Teensy 3.0
|
||||
# - PJRC_TEENSY_3_1 for Teensy 3.1 or 3.2
|
||||
# - MCHCK_K20 for Infinity KB
|
||||
#BOARD = MCHCK_K20
|
||||
BOARD = PJRC_TEENSY_3_1
|
||||
|
||||
# Cortex version
|
||||
# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4
|
||||
MCU = cortex-m4
|
||||
|
||||
# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7
|
||||
# I.e. 6 for Teensy LC; 7 for Teensy 3.x
|
||||
ARMV = 7
|
||||
|
||||
# Vector table for application
|
||||
# 0x00000000-0x00001000 area is occupied by bootlaoder.*/
|
||||
# The CORTEX_VTOR... is needed only for MCHCK/Infinity KB
|
||||
OPT_DEFS += -DCORTEX_VTOR_INIT=0x00002000
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
CUSTOM_MATRIX ?= yes # Custom matrix file
|
||||
SERIAL_LINK_ENABLE = yes
|
||||
VISUALIZER_ENABLE ?= no #temporarily disabled to make everything compile
|
||||
LCD_ENABLE ?= yes
|
||||
LED_ENABLE ?= yes
|
||||
LCD_BACKLIGHT_ENABLE ?= yes
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
|
||||
ifdef LCD_ENABLE
|
||||
include $(SUBPROJECT_PATH)/drivers/gdisp/st7565ergodox/driver.mk
|
||||
endif
|
||||
|
||||
ifdef LED_ENABLE
|
||||
include $(SUBPROJECT_PATH)/drivers/gdisp/IS31FL3731C/driver.mk
|
||||
endif
|
||||
@ -0,0 +1,73 @@
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
|
||||
# Build Options
|
||||
# change yes to no to disable
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
||||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
NKRO_ENABLE ?= no # USB Nkey Rollover
|
||||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
|
||||
MIDI_ENABLE ?= no # MIDI controls
|
||||
UNICODE_ENABLE ?= no # Unicode
|
||||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
|
||||
|
||||
@ -0,0 +1,73 @@
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
|
||||
# Build Options
|
||||
# change yes to no to disable
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
||||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
NKRO_ENABLE ?= no # USB Nkey Rollover
|
||||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
|
||||
MIDI_ENABLE ?= no # MIDI controls
|
||||
UNICODE_ENABLE ?= no # Unicode
|
||||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
|
||||
|
||||
@ -1,71 +1,3 @@
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
# Build Options
|
||||
# change to "no" to disable the options, or define them in the Makefile in
|
||||
# the appropriate keymap folder that will get included automatically
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= no # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
|
||||
MIDI_ENABLE ?= no # MIDI controls
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
UNICODE_ENABLE ?= no # Unicode
|
||||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
|
||||
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,67 @@
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=512
|
||||
|
||||
# Build Options
|
||||
# change to "no" to disable the options, or define them in the Makefile in
|
||||
# the appropriate keymap folder that will get included automatically
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= no # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
|
||||
MIDI_ENABLE ?= no # MIDI controls
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
UNICODE_ENABLE ?= no # Unicode
|
||||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
|
||||
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
||||
@ -1,3 +1,3 @@
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../Makefile
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,65 @@
|
||||
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= yes # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
||||
#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
|
||||
#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,89 @@
|
||||
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
# for avr upload
|
||||
USB ?= /dev/cu.usbmodem1421
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
|
||||
ifdef TEENSY2
|
||||
OPT_DEFS += -DATREUS_TEENSY2
|
||||
ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
|
||||
else
|
||||
OPT_DEFS += -DATREUS_ASTAR
|
||||
OPT_DEFS += -DCATERINA_BOOTLOADER
|
||||
ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
|
||||
avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
|
||||
endif
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# MCU name
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# change yes to no to disable
|
||||
#
|
||||
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE ?= no # Console for debug(+400)
|
||||
COMMAND_ENABLE ?= no # Commands for debug and configuration
|
||||
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
||||
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
||||
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
||||
NKRO_ENABLE ?= no # USB Nkey Rollover
|
||||
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
|
||||
MIDI_ENABLE ?= no # MIDI controls
|
||||
UNICODE_ENABLE ?= no # Unicode
|
||||
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
RGBLIGHT_ENABLE = yes
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
|
||||
upload: build
|
||||
$(ATREUS_UPLOAD_COMMAND)
|
||||
|
||||
@ -1,5 +1,3 @@
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,5 @@
|
||||
AUDIO_ENABLE ?= no # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -1,5 +1,3 @@
|
||||
AUDIO_ENABLE ?= yes # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
ifndef MAKEFILE_INCLUDED
|
||||
include ../../../Makefile
|
||||
endif
|
||||
@ -0,0 +1,5 @@
|
||||
AUDIO_ENABLE ?= yes # Audio output on port C6
|
||||
|
||||
ifndef QUANTUM_DIR
|
||||
include ../../../Makefile
|
||||
endif
|
||||
Loading…
Reference in New Issue