Add YMD96 Keyboard (#1838)
* add ymd96 base currently not working correctly. * Update honestly not really sure what I've been doing but I'm just more or less brute forcing this until I can get the pcb schematic or something * honestly just trying stuff out * Update keymaps Getting closer hopefully * ymd96 works! at least for me * Update readme * Update readme * Update readmetravis_phases
Andrew
7 years ago
committed by
Jack Humbert
parent
f9f3afd767
commit
6531d64ac7
@ -0,0 +1,62 @@
|
||||
YMD96
|
||||
==========================
|
||||
|
||||
This is a port of the QMK firmware for boards that are based on the
|
||||
ps2avrGB firmware, like the [ps2avrGB
|
||||
keyboard](https://www.keyclack.com/product/gb-ps2avrgb/), for use on the YMD96.
|
||||
|
||||
Note that this is a complete replacement for the firmware, so you won't be
|
||||
using Bootmapper Client to change any keyboard settings, since not all the
|
||||
USB report options are supported.
|
||||
|
||||
Here is the default layout, it is fairly simple with a few function keys:
|
||||
|
||||
If you have a different layout (since there were many options during the GB), please feel free to contribute!
|
||||
|
||||
Keyboard maintainer: [Andrew](https://github.com/sparkyman215)
|
||||
Hardware Supported: YMD96 with the ATmega32a chip.
|
||||
Hardware Availability: The GB was run June 2017, [in this thread](https://www.reddit.com/r/mechmarket/comments/6hu3yx/vendor_ymd96_gb_is_now_live_68_an_universal_and/). The vendor has stated that they plan on selling more rounds.
|
||||
|
||||
## Finding your specific matrix
|
||||
|
||||
This firmware was modified from [ps2avrGB](https://github.com/qmk/qmk_firmware/tree/master/keyboards/ps2avrGB), also found on this qmk repo, to work with the YMD96 keyboard. However, I only have one board to test with, which might have a different layout than yours. To get qmk working with your specific layout, you'll need to follow these steps:
|
||||
|
||||
1. Follow the [guide here](https://www.massdrop.com/talk/1392/programming-kbd-keyboards-via-bootmapper-client) to get Bootmapper Client setup. While you won't need it after you get qmk working, you need to use Bootmapper Client to figure out how the matrix is laid out. In the end, here's an example of what it should look like: 
|
||||
2. Next is the tricky part: editing the `ymd96.h` file. Here, you have to figure out how the keys are laid out physically and assign each key the right keycode. Study how the codes in brackets correspond to the BMC columns. Consider the first column: K000 corresponds to Col 1 Row 1, and K100 corresponds to Col 2 Row 1. K111 = Col 2 Row 10.
|
||||
3. First, you need to define the codes that are actually used in the brackets. KC_NO is used whenever a cell isn't used, such as col 1 row 4-6 in BMC.
|
||||
4. Once you have all those set up, you need to put the keycodes where they physically are in the KEYMAP( area. Since the columns aren't all uniform (e.g. col2row6 is B, but col2row7 is the numpad 1), the keycodes will be all over the place.
|
||||
5. Finally! Hard part is pretty much done. Next, you simply have to edit the `keymap.c` file to actually assign the keycodes to do something. You essentially replace the keycodes (e.g. K000) with actual codes that do something, e.g. KC_ENTER. Modify these to your hearts content, and of course this is where all the extra functionality of QMK shines. I won't get into it here, but hopefully you've made it this far!
|
||||
|
||||
## Installing and Building
|
||||
|
||||
First, install the requirements. These commands are for OSX, but all you
|
||||
need is the AVR toolchain and `bootloadHID` for flashing:
|
||||
|
||||
```
|
||||
$ brew cask install crosspack-avr
|
||||
$ brew install --HEAD https://raw.githubusercontent.com/robertgzr/homebrew-tap/master/bootloadhid.rb
|
||||
```
|
||||
|
||||
In order to use the `./program` script, which can reboot the board into
|
||||
the bootloader, you'll need Python 2 with PyUSB installed:
|
||||
|
||||
```
|
||||
$ pip install pyusb
|
||||
```
|
||||
|
||||
Build the keyboard with
|
||||
```
|
||||
$ make ymd96-default
|
||||
```
|
||||
If you make your own layout, change the `default` word to whatever your layout is.
|
||||
|
||||
## Troubleshooting
|
||||
|
||||
From my experience, it's really hard to brick these boards. But these
|
||||
tricks have been useful when it got stuck in a weird scenario.
|
||||
|
||||
1. Try plugging the board in while pressing `L_Ctrl`. This will force it
|
||||
to boot only the bootloader without loading the firmware. Once this is
|
||||
done, just reflash the board with the original firmware.
|
||||
2. Sometimes USB hubs can act weird, so try connecting the board directly
|
||||
to your computer or plugging/unplugging the USB hub.
|
||||
@ -0,0 +1,43 @@
|
||||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef CONFIG_H
|
||||
#define CONFIG_H
|
||||
|
||||
#define VENDOR_ID 0x20A0
|
||||
#define PRODUCT_ID 0x422D
|
||||
// TODO: share these strings with usbconfig.h
|
||||
// Edit usbconfig.h to change these.
|
||||
#define MANUFACTURER ymdkey
|
||||
#define PRODUCT ymd96
|
||||
|
||||
/* matrix size */
|
||||
#define MATRIX_ROWS 8
|
||||
#define MATRIX_COLS 15
|
||||
#define DIODE_DIRECTION ROW2COL
|
||||
|
||||
#define RGBLED_NUM 20
|
||||
#define RGBLIGHT_ANIMATIONS
|
||||
|
||||
#define NO_UART 1
|
||||
#define BOOTLOADHID_BOOTLOADER 1
|
||||
|
||||
/* key combination for command */
|
||||
#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,104 @@
|
||||
/*
|
||||
Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include <avr/io.h>
|
||||
#include <util/twi.h>
|
||||
|
||||
#include "i2c.h"
|
||||
|
||||
void i2c_set_bitrate(uint16_t bitrate_khz) {
|
||||
uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
|
||||
if (bitrate_div >= 16) {
|
||||
bitrate_div = (bitrate_div - 16) / 2;
|
||||
}
|
||||
TWBR = bitrate_div;
|
||||
}
|
||||
|
||||
void i2c_init(void) {
|
||||
// set pull-up resistors on I2C bus pins
|
||||
PORTC |= 0b11;
|
||||
|
||||
i2c_set_bitrate(400);
|
||||
|
||||
// enable TWI (two-wire interface)
|
||||
TWCR |= (1 << TWEN);
|
||||
|
||||
// enable TWI interrupt and slave address ACK
|
||||
TWCR |= (1 << TWIE);
|
||||
TWCR |= (1 << TWEA);
|
||||
}
|
||||
|
||||
uint8_t i2c_start(uint8_t address) {
|
||||
// reset TWI control register
|
||||
TWCR = 0;
|
||||
|
||||
// begin transmission and wait for it to end
|
||||
TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
|
||||
while (!(TWCR & (1<<TWINT)));
|
||||
|
||||
// check if the start condition was successfully transmitted
|
||||
if ((TWSR & 0xF8) != TW_START) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
// transmit address and wait
|
||||
TWDR = address;
|
||||
TWCR = (1<<TWINT) | (1<<TWEN);
|
||||
while (!(TWCR & (1<<TWINT)));
|
||||
|
||||
// check if the device has acknowledged the READ / WRITE mode
|
||||
uint8_t twst = TW_STATUS & 0xF8;
|
||||
if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
void i2c_stop(void) {
|
||||
TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
|
||||
}
|
||||
|
||||
uint8_t i2c_write(uint8_t data) {
|
||||
TWDR = data;
|
||||
|
||||
// transmit data and wait
|
||||
TWCR = (1<<TWINT) | (1<<TWEN);
|
||||
while (!(TWCR & (1<<TWINT)));
|
||||
|
||||
if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
|
||||
if (i2c_start(address)) {
|
||||
return 1;
|
||||
}
|
||||
|
||||
for (uint16_t i = 0; i < length; i++) {
|
||||
if (i2c_write(data[i])) {
|
||||
return 1;
|
||||
}
|
||||
}
|
||||
|
||||
i2c_stop();
|
||||
|
||||
return 0;
|
||||
}
|
||||
@ -0,0 +1,25 @@
|
||||
/*
|
||||
Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef __I2C_H__
|
||||
#define __I2C_H__
|
||||
|
||||
void i2c_init(void);
|
||||
void i2c_set_bitrate(uint16_t bitrate_khz);
|
||||
uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length);
|
||||
|
||||
#endif
|
||||
@ -0,0 +1,62 @@
|
||||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public LicensezZZ
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include "ymd96.h"
|
||||
#include "action_layer.h"
|
||||
#include "rgblight.h"
|
||||
|
||||
#define ______ KC_TRNS
|
||||
#define _DEFLT 0
|
||||
#define _RAISE 1
|
||||
|
||||
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
|
||||
|
||||
/* Layer 0, default layer
|
||||
* | Esc | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 |Print | Home | End |Insert|Delete| PgUp | 19 keys
|
||||
* | ~` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = | BkSpc |NumLck| / | * | PgDn | 18 keys
|
||||
* | Tab | Q | W | E | R | T | Y | U | I | O | P | { | } | \ | 7 | 8 | 9 | - | 18 keys
|
||||
* | Caps | A | S | D | F | G | H | J | K | L | ; | ' | Return | 4 | 5 | 6 | + | 17 keys
|
||||
* | LShft | Z | X | C | V | B | N | M | , | . | / | RShft | 1 | 2 | 3 | En | 16 keys
|
||||
* | Ctrl | Win | Alt | Space | Fn | Win | Left | Down | Up | Right| 0 | . | ter | 12 keys
|
||||
*/
|
||||
|
||||
[_DEFLT] = KEYMAP(
|
||||
KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_HOME, KC_END, KC_INSERT, KC_DELETE, KC_PGUP, \
|
||||
KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_NUMLOCK, KC_KP_SLASH, KC_KP_ASTERISK, KC_PGDN, \
|
||||
KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_P7, KC_P8, KC_P9, KC_PMNS, \
|
||||
KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, KC_PPLS, \
|
||||
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_RSFT, KC_P1, KC_P2, KC_P3, KC_PENT, \
|
||||
KC_LCTL, KC_LGUI,KC_LALT, KC_SPC, MO(_RAISE), KC_RGUI, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT, KC_P0, KC_PDOT \
|
||||
),
|
||||
/* Layer 1, raise layer
|
||||
* | | | | | | | | | | | | | | | | | | | |
|
||||
* | | | | | | | | | | | | | | | | | | |
|
||||
* | | | | | | | | | | | | | | | | | | |
|
||||
* | | | | | | | | | | | | | | | | | |
|
||||
* | | | | | | | | | VolDn| VolUp| Mute | Play/Pause | | | | |
|
||||
* | | | | | | | | | | | | | |
|
||||
*/
|
||||
[_RAISE] = KEYMAP(
|
||||
______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \
|
||||
______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \
|
||||
______, ______, ______, ______, ______, ______, ______, ______, ______, ______, KC_F22, KC_F23, KC_F24, ______, ______, ______, ______, ______, \
|
||||
______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, \
|
||||
______, ______, ______, ______, ______, ______, ______, ______, KC_VOLD,KC_VOLU, KC_MUTE, KC_MPLY, ______, ______, ______, ______, \
|
||||
______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______, ______ \
|
||||
)
|
||||
};
|
||||
@ -0,0 +1,106 @@
|
||||
/*
|
||||
Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include <avr/io.h>
|
||||
#include <util/delay.h>
|
||||
|
||||
#include "matrix.h"
|
||||
|
||||
#ifndef DEBOUNCE
|
||||
# define DEBOUNCE 5
|
||||
#endif
|
||||
|
||||
static uint8_t debouncing = DEBOUNCE;
|
||||
|
||||
static matrix_row_t matrix[MATRIX_ROWS];
|
||||
static matrix_row_t matrix_debouncing[MATRIX_ROWS];
|
||||
|
||||
void matrix_init(void) {
|
||||
// all outputs for rows high
|
||||
DDRB = 0xFF;
|
||||
PORTB = 0xFF;
|
||||
// all inputs for columns
|
||||
DDRA = 0x00;
|
||||
DDRC &= ~(0x111111<<2);
|
||||
DDRD &= ~(1<<PIND7);
|
||||
// all columns are pulled-up
|
||||
PORTA = 0xFF;
|
||||
PORTC |= (0b111111<<2);
|
||||
PORTD |= (1<<PIND7);
|
||||
|
||||
// initialize matrix state: all keys off
|
||||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
|
||||
matrix[row] = 0x00;
|
||||
matrix_debouncing[row] = 0x00;
|
||||
}
|
||||
}
|
||||
|
||||
void matrix_set_row_status(uint8_t row) {
|
||||
DDRB = (1 << row);
|
||||
PORTB = ~(1 << row);
|
||||
}
|
||||
|
||||
uint8_t bit_reverse(uint8_t x) {
|
||||
x = ((x >> 1) & 0x55) | ((x << 1) & 0xaa);
|
||||
x = ((x >> 2) & 0x33) | ((x << 2) & 0xcc);
|
||||
x = ((x >> 4) & 0x0f) | ((x << 4) & 0xf0);
|
||||
return x;
|
||||
}
|
||||
|
||||
uint8_t matrix_scan(void) {
|
||||
for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
|
||||
matrix_set_row_status(row);
|
||||
_delay_us(5);
|
||||
|
||||
matrix_row_t cols = (
|
||||
// cols 0..7, PORTA 0 -> 7
|
||||
(~PINA) & 0xFF
|
||||
) | (
|
||||
// cols 8..13, PORTC 7 -> 0
|
||||
bit_reverse((~PINC) & 0xFF) << 8
|
||||
) | (
|
||||
// col 14, PORTD 7
|
||||
((~PIND) & (1 << PIND7)) << 7
|
||||
);
|
||||
|
||||
if (matrix_debouncing[row] != cols) {
|
||||
matrix_debouncing[row] = cols;
|
||||
debouncing = DEBOUNCE;
|
||||
}
|
||||
}
|
||||
|
||||
if (debouncing) {
|
||||
if (--debouncing) {
|
||||
_delay_ms(1);
|
||||
} else {
|
||||
for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
|
||||
matrix[i] = matrix_debouncing[i];
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
matrix_scan_user();
|
||||
|
||||
return 1;
|
||||
}
|
||||
|
||||
inline matrix_row_t matrix_get_row(uint8_t row) {
|
||||
return matrix[row];
|
||||
}
|
||||
|
||||
void matrix_print(void) {
|
||||
}
|
||||
@ -0,0 +1,74 @@
|
||||
#!/usr/bin/env python
|
||||
# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
#
|
||||
# This program is free software: you can redistribute it and/or modify
|
||||
# it under the terms of the GNU General Public License as published by
|
||||
# the Free Software Foundation, either version 2 of the License, or
|
||||
# (at your option) any later version.
|
||||
#
|
||||
# This program is distributed in the hope that it will be useful,
|
||||
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
# GNU General Public License for more details.
|
||||
#
|
||||
# You should have received a copy of the GNU General Public License
|
||||
# along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
||||
from __future__ import print_function
|
||||
|
||||
import os
|
||||
import sys
|
||||
import time
|
||||
import usb
|
||||
|
||||
if len(sys.argv) < 2:
|
||||
print('Usage: %s <firmware.hex>' % sys.argv[0])
|
||||
sys.exit(1)
|
||||
|
||||
print('Searching for ps2avrGB... ', end='')
|
||||
|
||||
dev = usb.core.find(idVendor=0x20A0, idProduct=0x422D)
|
||||
if dev is None:
|
||||
raise ValueError('Device not found')
|
||||
|
||||
print('Found', end='\n\n')
|
||||
|
||||
print('Device Information:')
|
||||
print(' idVendor: %d (0x%04x)' % (dev.idVendor, dev.idVendor))
|
||||
print(' idProduct: %d (0x%04x)' % (dev.idProduct, dev.idProduct))
|
||||
print('Manufacturer: %s' % (dev.iManufacturer))
|
||||
print('Serial: %s' % (dev.iSerialNumber))
|
||||
print('Product: %s' % (dev.iProduct), end='\n\n')
|
||||
|
||||
print('Transferring control to bootloader... ', end='')
|
||||
|
||||
dev.set_configuration()
|
||||
|
||||
request_type = usb.util.build_request_type(
|
||||
usb.util.CTRL_OUT,
|
||||
usb.util.CTRL_TYPE_CLASS,
|
||||
usb.util.CTRL_RECIPIENT_DEVICE)
|
||||
|
||||
USBRQ_HID_SET_REPORT = 0x09
|
||||
HID_REPORT_OPTION = 0x0301
|
||||
|
||||
|
||||
try:
|
||||
dev.ctrl_transfer(
|
||||
request_type,
|
||||
USBRQ_HID_SET_REPORT,
|
||||
HID_REPORT_OPTION,
|
||||
0,
|
||||
[0, 0, 0xFF] + [0] * 5
|
||||
)
|
||||
except usb.core.USBError:
|
||||
# for some reason I keep getting USBError, but it works!
|
||||
pass
|
||||
|
||||
# wait a bit until bootloader starts up
|
||||
time.sleep(2)
|
||||
|
||||
print('OK')
|
||||
print('Programming...')
|
||||
if os.system('bootloadHID -r "%s"' % sys.argv[1]) == 0:
|
||||
print('\nDone!')
|
||||
@ -0,0 +1,45 @@
|
||||
# Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
#
|
||||
# This program is free software: you can redistribute it and/or modify
|
||||
# it under the terms of the GNU General Public License as published by
|
||||
# the Free Software Foundation, either version 2 of the License, or
|
||||
# (at your option) any later version.
|
||||
#
|
||||
# This program is distributed in the hope that it will be useful,
|
||||
# but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
# GNU General Public License for more details.
|
||||
#
|
||||
# You should have received a copy of the GNU General Public License
|
||||
# along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
||||
# MCU name
|
||||
MCU = atmega32a
|
||||
PROTOCOL = VUSB
|
||||
|
||||
# unsupported features for now
|
||||
NO_UART = yes
|
||||
NO_SUSPEND_POWER_DOWN = yes
|
||||
|
||||
# processor frequency
|
||||
F_CPU = 12000000
|
||||
|
||||
# build options
|
||||
BOOTMAGIC_ENABLE = yes
|
||||
MOUSEKEY_ENABLE = yes
|
||||
EXTRAKEY_ENABLE = yes
|
||||
CONSOLE_ENABLE = yes
|
||||
COMMAND_ENABLE = yes
|
||||
BACKLIGHT_ENABLE = no
|
||||
RGBLIGHT_ENABLE = yes
|
||||
RGBLIGHT_CUSTOM_DRIVER = yes
|
||||
|
||||
OPT_DEFS = -DDEBUG_LEVEL=0
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=2048
|
||||
|
||||
# custom matrix setup
|
||||
CUSTOM_MATRIX = yes
|
||||
SRC = matrix.c i2c.c
|
||||
|
||||
# programming options
|
||||
PROGRAM_CMD = ./keyboards/ps2avrGB/program $(TARGET).hex
|
||||
@ -0,0 +1,396 @@
|
||||
/* Name: usbconfig.h
|
||||
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||||
* Author: Christian Starkjohann
|
||||
* Creation Date: 2005-04-01
|
||||
* Tabsize: 4
|
||||
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
||||
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||||
* This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
|
||||
*/
|
||||
|
||||
#ifndef __usbconfig_h_included__
|
||||
#define __usbconfig_h_included__
|
||||
|
||||
#include "config.h"
|
||||
|
||||
/*
|
||||
General Description:
|
||||
This file is an example configuration (with inline documentation) for the USB
|
||||
driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
|
||||
also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
|
||||
wire the lines to any other port, as long as D+ is also wired to INT0 (or any
|
||||
other hardware interrupt, as long as it is the highest level interrupt, see
|
||||
section at the end of this file).
|
||||
*/
|
||||
|
||||
/* ---------------------------- Hardware Config ---------------------------- */
|
||||
|
||||
#define USB_CFG_IOPORTNAME D
|
||||
/* This is the port where the USB bus is connected. When you configure it to
|
||||
* "B", the registers PORTB, PINB and DDRB will be used.
|
||||
*/
|
||||
#define USB_CFG_DMINUS_BIT 3
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
||||
* This may be any bit in the port.
|
||||
*/
|
||||
#define USB_CFG_DPLUS_BIT 2
|
||||
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
||||
* This may be any bit in the port. Please note that D+ must also be connected
|
||||
* to interrupt pin INT0! [You can also use other interrupts, see section
|
||||
* "Optional MCU Description" below, or you can connect D- to the interrupt, as
|
||||
* it is required if you use the USB_COUNT_SOF feature. If you use D- for the
|
||||
* interrupt, the USB interrupt will also be triggered at Start-Of-Frame
|
||||
* markers every millisecond.]
|
||||
*/
|
||||
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
||||
/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
|
||||
* 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
|
||||
* require no crystal, they tolerate +/- 1% deviation from the nominal
|
||||
* frequency. All other rates require a precision of 2000 ppm and thus a
|
||||
* crystal!
|
||||
* Since F_CPU should be defined to your actual clock rate anyway, you should
|
||||
* not need to modify this setting.
|
||||
*/
|
||||
#define USB_CFG_CHECK_CRC 0
|
||||
/* Define this to 1 if you want that the driver checks integrity of incoming
|
||||
* data packets (CRC checks). CRC checks cost quite a bit of code size and are
|
||||
* currently only available for 18 MHz crystal clock. You must choose
|
||||
* USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional Hardware Config ------------------------ */
|
||||
|
||||
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
||||
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
||||
* V+, you can connect and disconnect the device from firmware by calling
|
||||
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
||||
* This constant defines the port on which the pullup resistor is connected.
|
||||
*/
|
||||
/* #define USB_CFG_PULLUP_BIT 4 */
|
||||
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
||||
* above) where the 1.5k pullup resistor is connected. See description
|
||||
* above for details.
|
||||
*/
|
||||
|
||||
/* --------------------------- Functional Range ---------------------------- */
|
||||
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
||||
/* Define this to 1 if you want to compile a version with two endpoints: The
|
||||
* default control endpoint 0 and an interrupt-in endpoint (any other endpoint
|
||||
* number).
|
||||
*/
|
||||
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 1
|
||||
/* Define this to 1 if you want to compile a version with three endpoints: The
|
||||
* default control endpoint 0, an interrupt-in endpoint 3 (or the number
|
||||
* configured below) and a catch-all default interrupt-in endpoint as above.
|
||||
* You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
|
||||
*/
|
||||
#define USB_CFG_EP3_NUMBER 3
|
||||
/* If the so-called endpoint 3 is used, it can now be configured to any other
|
||||
* endpoint number (except 0) with this macro. Default if undefined is 3.
|
||||
*/
|
||||
/* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
|
||||
/* The above macro defines the startup condition for data toggling on the
|
||||
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
|
||||
* Since the token is toggled BEFORE sending any data, the first packet is
|
||||
* sent with the oposite value of this configuration!
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_HALT 0
|
||||
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
||||
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
||||
* it is required by the standard. We have made it a config option because it
|
||||
* bloats the code considerably.
|
||||
*/
|
||||
#define USB_CFG_SUPPRESS_INTR_CODE 0
|
||||
/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
|
||||
* want to send any data over them. If this macro is defined to 1, functions
|
||||
* usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
|
||||
* you need the interrupt-in endpoints in order to comply to an interface
|
||||
* (e.g. HID), but never want to send any data. This option saves a couple
|
||||
* of bytes in flash memory and the transmit buffers in RAM.
|
||||
*/
|
||||
#define USB_CFG_INTR_POLL_INTERVAL 1
|
||||
/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
|
||||
* interval. The value is in milliseconds and must not be less than 10 ms for
|
||||
* low speed devices.
|
||||
*/
|
||||
#define USB_CFG_IS_SELF_POWERED 0
|
||||
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
||||
* device is powered from the USB bus.
|
||||
*/
|
||||
#define USB_CFG_MAX_BUS_POWER 500
|
||||
/* Set this variable to the maximum USB bus power consumption of your device.
|
||||
* The value is in milliamperes. [It will be divided by two since USB
|
||||
* communicates power requirements in units of 2 mA.]
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITE 1
|
||||
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
||||
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
||||
* bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_READ 0
|
||||
/* Set this to 1 if you need to send control replies which are generated
|
||||
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
||||
* data from a static buffer, set it to 0 and return the data from
|
||||
* usbFunctionSetup(). This saves a couple of bytes.
|
||||
*/
|
||||
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
||||
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
|
||||
* You must implement the function usbFunctionWriteOut() which receives all
|
||||
* interrupt/bulk data sent to any endpoint other than 0. The endpoint number
|
||||
* can be found in 'usbRxToken'.
|
||||
*/
|
||||
#define USB_CFG_HAVE_FLOWCONTROL 0
|
||||
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
||||
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
||||
* usbdrv.h.
|
||||
*/
|
||||
#define USB_CFG_DRIVER_FLASH_PAGE 0
|
||||
/* If the device has more than 64 kBytes of flash, define this to the 64 k page
|
||||
* where the driver's constants (descriptors) are located. Or in other words:
|
||||
* Define this to 1 for boot loaders on the ATMega128.
|
||||
*/
|
||||
#define USB_CFG_LONG_TRANSFERS 0
|
||||
/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
|
||||
* in a single control-in or control-out transfer. Note that the capability
|
||||
* for long transfers increases the driver size.
|
||||
*/
|
||||
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
||||
/* This macro is a hook if you want to do unconventional things. If it is
|
||||
* defined, it's inserted at the beginning of received message processing.
|
||||
* If you eat the received message and don't want default processing to
|
||||
* proceed, do a return after doing your things. One possible application
|
||||
* (besides debugging) is to flash a status LED on each packet.
|
||||
*/
|
||||
/* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
|
||||
/* This macro is a hook if you need to know when an USB RESET occurs. It has
|
||||
* one parameter which distinguishes between the start of RESET state and its
|
||||
* end.
|
||||
*/
|
||||
/* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
|
||||
/* This macro (if defined) is executed when a USB SET_ADDRESS request was
|
||||
* received.
|
||||
*/
|
||||
#define USB_COUNT_SOF 1
|
||||
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
||||
* counts SOF packets. This feature requires that the hardware interrupt is
|
||||
* connected to D- instead of D+.
|
||||
*/
|
||||
/* #ifdef __ASSEMBLER__
|
||||
* macro myAssemblerMacro
|
||||
* in YL, TCNT0
|
||||
* sts timer0Snapshot, YL
|
||||
* endm
|
||||
* #endif
|
||||
* #define USB_SOF_HOOK myAssemblerMacro
|
||||
* This macro (if defined) is executed in the assembler module when a
|
||||
* Start Of Frame condition is detected. It is recommended to define it to
|
||||
* the name of an assembler macro which is defined here as well so that more
|
||||
* than one assembler instruction can be used. The macro may use the register
|
||||
* YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
|
||||
* immediately after an SOF pulse may be lost and must be retried by the host.
|
||||
* What can you do with this hook? Since the SOF signal occurs exactly every
|
||||
* 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
|
||||
* designs running on the internal RC oscillator.
|
||||
* Please note that Start Of Frame detection works only if D- is wired to the
|
||||
* interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
|
||||
*/
|
||||
#define USB_CFG_CHECK_DATA_TOGGLING 0
|
||||
/* define this macro to 1 if you want to filter out duplicate data packets
|
||||
* sent by the host. Duplicates occur only as a consequence of communication
|
||||
* errors, when the host does not receive an ACK. Please note that you need to
|
||||
* implement the filtering yourself in usbFunctionWriteOut() and
|
||||
* usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
|
||||
* for each control- and out-endpoint to check for duplicate packets.
|
||||
*/
|
||||
#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
|
||||
/* define this macro to 1 if you want the function usbMeasureFrameLength()
|
||||
* compiled in. This function can be used to calibrate the AVR's RC oscillator.
|
||||
*/
|
||||
#define USB_USE_FAST_CRC 0
|
||||
/* The assembler module has two implementations for the CRC algorithm. One is
|
||||
* faster, the other is smaller. This CRC routine is only used for transmitted
|
||||
* messages where timing is not critical. The faster routine needs 31 cycles
|
||||
* per byte while the smaller one needs 61 to 69 cycles. The faster routine
|
||||
* may be worth the 32 bytes bigger code size if you transmit lots of data and
|
||||
* run the AVR close to its limit.
|
||||
*/
|
||||
|
||||
/* -------------------------- Device Description --------------------------- */
|
||||
|
||||
#define USB_CFG_VENDOR_ID (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
|
||||
/* USB vendor ID for the device, low byte first. If you have registered your
|
||||
* own Vendor ID, define it here. Otherwise you may use one of obdev's free
|
||||
* shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_ID (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
|
||||
/* This is the ID of the product, low byte first. It is interpreted in the
|
||||
* scope of the vendor ID. If you have registered your own VID with usb.org
|
||||
* or if you have licensed a PID from somebody else, define it here. Otherwise
|
||||
* you may use one of obdev's free shared VID/PID pairs. See the file
|
||||
* USB-IDs-for-free.txt for details!
|
||||
* *** IMPORTANT NOTE ***
|
||||
* This template uses obdev's shared VID/PID pair for Vendor Class devices
|
||||
* with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
|
||||
* the implications!
|
||||
*/
|
||||
#define USB_CFG_DEVICE_VERSION 0x00, 0x02
|
||||
/* Version number of the device: Minor number first, then major number.
|
||||
*/
|
||||
#define USB_CFG_VENDOR_NAME 'w', 'i', 'n', 'k', 'e', 'y', 'l', 'e', 's', 's', '.', 'k', 'r'
|
||||
#define USB_CFG_VENDOR_NAME_LEN 13
|
||||
/* These two values define the vendor name returned by the USB device. The name
|
||||
* must be given as a list of characters under single quotes. The characters
|
||||
* are interpreted as Unicode (UTF-16) entities.
|
||||
* If you don't want a vendor name string, undefine these macros.
|
||||
* ALWAYS define a vendor name containing your Internet domain name if you use
|
||||
* obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
|
||||
* details.
|
||||
*/
|
||||
#define USB_CFG_DEVICE_NAME 'p', 's', '2', 'a', 'v', 'r', 'G', 'B'
|
||||
#define USB_CFG_DEVICE_NAME_LEN 8
|
||||
/* Same as above for the device name. If you don't want a device name, undefine
|
||||
* the macros. See the file USB-IDs-for-free.txt before you assign a name if
|
||||
* you use a shared VID/PID.
|
||||
*/
|
||||
/*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
|
||||
/*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
|
||||
/* Same as above for the serial number. If you don't want a serial number,
|
||||
* undefine the macros.
|
||||
* It may be useful to provide the serial number through other means than at
|
||||
* compile time. See the section about descriptor properties below for how
|
||||
* to fine tune control over USB descriptors such as the string descriptor
|
||||
* for the serial number.
|
||||
*/
|
||||
#define USB_CFG_DEVICE_CLASS 0
|
||||
#define USB_CFG_DEVICE_SUBCLASS 0
|
||||
/* See USB specification if you want to conform to an existing device class.
|
||||
* Class 0xff is "vendor specific".
|
||||
*/
|
||||
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
||||
#define USB_CFG_INTERFACE_SUBCLASS 1 /* Boot */
|
||||
#define USB_CFG_INTERFACE_PROTOCOL 1 /* Keyboard */
|
||||
/* See USB specification if you want to conform to an existing device class or
|
||||
* protocol. The following classes must be set at interface level:
|
||||
* HID class is 3, no subclass and protocol required (but may be useful!)
|
||||
* CDC class is 2, use subclass 2 and protocol 1 for ACM
|
||||
*/
|
||||
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0
|
||||
/* Define this to the length of the HID report descriptor, if you implement
|
||||
* an HID device. Otherwise don't define it or define it to 0.
|
||||
* If you use this define, you must add a PROGMEM character array named
|
||||
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
||||
* Don't forget to keep the array and this define in sync!
|
||||
*/
|
||||
|
||||
/* #define USB_PUBLIC static */
|
||||
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
||||
* This technique saves a couple of bytes in flash memory.
|
||||
*/
|
||||
|
||||
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
||||
/* If you don't want to use the driver's default USB descriptors, you can
|
||||
* provide our own. These can be provided as (1) fixed length static data in
|
||||
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
||||
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
||||
* information about this function.
|
||||
* Descriptor handling is configured through the descriptor's properties. If
|
||||
* no properties are defined or if they are 0, the default descriptor is used.
|
||||
* Possible properties are:
|
||||
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
||||
* at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
|
||||
* used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
|
||||
* you want RAM pointers.
|
||||
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
||||
* in static memory is in RAM, not in flash memory.
|
||||
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
||||
* the driver must know the descriptor's length. The descriptor itself is
|
||||
* found at the address of a well known identifier (see below).
|
||||
* List of static descriptor names (must be declared PROGMEM if in flash):
|
||||
* char usbDescriptorDevice[];
|
||||
* char usbDescriptorConfiguration[];
|
||||
* char usbDescriptorHidReport[];
|
||||
* char usbDescriptorString0[];
|
||||
* int usbDescriptorStringVendor[];
|
||||
* int usbDescriptorStringDevice[];
|
||||
* int usbDescriptorStringSerialNumber[];
|
||||
* Other descriptors can't be provided statically, they must be provided
|
||||
* dynamically at runtime.
|
||||
*
|
||||
* Descriptor properties are or-ed or added together, e.g.:
|
||||
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
||||
*
|
||||
* The following descriptors are defined:
|
||||
* USB_CFG_DESCR_PROPS_DEVICE
|
||||
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
||||
* USB_CFG_DESCR_PROPS_STRINGS
|
||||
* USB_CFG_DESCR_PROPS_STRING_0
|
||||
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
||||
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
||||
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
||||
* USB_CFG_DESCR_PROPS_HID
|
||||
* USB_CFG_DESCR_PROPS_HID_REPORT
|
||||
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
||||
*
|
||||
* Note about string descriptors: String descriptors are not just strings, they
|
||||
* are Unicode strings prefixed with a 2 byte header. Example:
|
||||
* int serialNumberDescriptor[] = {
|
||||
* USB_STRING_DESCRIPTOR_HEADER(6),
|
||||
* 'S', 'e', 'r', 'i', 'a', 'l'
|
||||
* };
|
||||
*/
|
||||
|
||||
#define USB_CFG_DESCR_PROPS_DEVICE 0
|
||||
#define USB_CFG_DESCR_PROPS_CONFIGURATION USB_PROP_IS_DYNAMIC
|
||||
//#define USB_CFG_DESCR_PROPS_CONFIGURATION 0
|
||||
#define USB_CFG_DESCR_PROPS_STRINGS 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_0 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
|
||||
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
|
||||
#define USB_CFG_DESCR_PROPS_HID USB_PROP_IS_DYNAMIC
|
||||
//#define USB_CFG_DESCR_PROPS_HID 0
|
||||
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
||||
//#define USB_CFG_DESCR_PROPS_HID_REPORT 0
|
||||
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
||||
|
||||
#define usbMsgPtr_t unsigned short
|
||||
/* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
|
||||
* a scalar type here because gcc generates slightly shorter code for scalar
|
||||
* arithmetics than for pointer arithmetics. Remove this define for backward
|
||||
* type compatibility or define it to an 8 bit type if you use data in RAM only
|
||||
* and all RAM is below 256 bytes (tiny memory model in IAR CC).
|
||||
*/
|
||||
|
||||
/* ----------------------- Optional MCU Description ------------------------ */
|
||||
|
||||
/* The following configurations have working defaults in usbdrv.h. You
|
||||
* usually don't need to set them explicitly. Only if you want to run
|
||||
* the driver on a device which is not yet supported or with a compiler
|
||||
* which is not fully supported (such as IAR C) or if you use a differnt
|
||||
* interrupt than INT0, you may have to define some of these.
|
||||
*/
|
||||
/* #define USB_INTR_CFG MCUCR */
|
||||
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE GIMSK */
|
||||
/* #define USB_INTR_ENABLE_BIT INT0 */
|
||||
/* #define USB_INTR_PENDING GIFR */
|
||||
/* #define USB_INTR_PENDING_BIT INTF0 */
|
||||
/* #define USB_INTR_VECTOR INT0_vect */
|
||||
|
||||
/* Set INT1 for D- falling edge to count SOF */
|
||||
/* #define USB_INTR_CFG EICRA */
|
||||
#define USB_INTR_CFG_SET ((1 << ISC11) | (0 << ISC10))
|
||||
/* #define USB_INTR_CFG_CLR 0 */
|
||||
/* #define USB_INTR_ENABLE EIMSK */
|
||||
#define USB_INTR_ENABLE_BIT INT1
|
||||
/* #define USB_INTR_PENDING EIFR */
|
||||
#define USB_INTR_PENDING_BIT INTF1
|
||||
#define USB_INTR_VECTOR INT1_vect
|
||||
|
||||
#endif /* __usbconfig_h_included__ */
|
||||
@ -0,0 +1,45 @@
|
||||
/*
|
||||
Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include "ymd96.h"
|
||||
#include "rgblight.h"
|
||||
|
||||
#include <avr/pgmspace.h>
|
||||
|
||||
#include "action_layer.h"
|
||||
#include "i2c.h"
|
||||
#include "quantum.h"
|
||||
|
||||
extern rgblight_config_t rgblight_config;
|
||||
|
||||
void rgblight_set(void) {
|
||||
if (!rgblight_config.enable) {
|
||||
for (uint8_t i = 0; i < RGBLED_NUM; i++) {
|
||||
led[i].r = 0;
|
||||
led[i].g = 0;
|
||||
led[i].b = 0;
|
||||
}
|
||||
}
|
||||
|
||||
i2c_init();
|
||||
i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
|
||||
}
|
||||
|
||||
__attribute__ ((weak))
|
||||
void matrix_scan_user(void) {
|
||||
rgblight_task();
|
||||
}
|
||||
@ -0,0 +1,55 @@
|
||||
/*
|
||||
Base Copyright 2017 Luiz Ribeiro <luizribeiro@gmail.com>
|
||||
Modified 2017 Andrew Novak <ndrw.nvk@gmail.com>
|
||||
|
||||
This program is free software: you can redistribute it and/or modify
|
||||
it under the terms of the GNU General Public License as published by
|
||||
the Free Software Foundation, either version 2 of the License, or
|
||||
(at your option) any later version.
|
||||
|
||||
This program is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
GNU General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU General Public License
|
||||
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#ifndef KEYMAP_COMMON_H
|
||||
#define KEYMAP_COMMON_H
|
||||
|
||||
#include "quantum_keycodes.h"
|
||||
#include "keycode.h"
|
||||
#include "action.h"
|
||||
|
||||
#define KEYMAP( \
|
||||
K500, K502, K503, K504, K505, K600, K610, K710, K700, K511, K512, K513, K514, K113, K214, K013, K706, K709, K708, \
|
||||
K400, K401, K402, K403, K404, K405, K601, K611, K711, K701, K410, K411, K412, K414, K406, K407, K408, K409, \
|
||||
K300, K301, K302, K303, K304, K305, K602, K612, K712, K702, K310, K311, K312, K313, K306, K307, K308, K309, \
|
||||
K200, K201, K202, K203, K204, K205, K603, K613, K713, K703, K210, K211, K213, K206, K207, K208, K209, \
|
||||
K100, K101, K102, K103, K104, K105, K604, K614, K714, K704, K110, K111, K106, K107, K108, K009, \
|
||||
K000, K001, K002, K605, K705, K010, K011, K606, K607, K609, K006, K008 \
|
||||
) { \
|
||||
{ K000, K001, K002, KC_NO, KC_NO, KC_NO, K006, KC_NO, K008, K009, K010, K011, KC_NO, K013, KC_NO, }, \
|
||||
{ K100, K101, K102, K103, K104, K105, K106, K107, K108, KC_NO, K110, K111, KC_NO, K113, KC_NO, }, \
|
||||
{ K200, K201, K202, K203, K204, K205, K206, K207, K208, K209, K210, K211, KC_NO, K213, K214, }, \
|
||||
{ K300, K301, K302, K303, K304, K305, K306, K307, K308, K309, K310, K311, K312, K313, KC_NO, }, \
|
||||
{ K400, K401, K402, K403, K404, K405, K406, K407, K408, K409, K410, K411, K412, KC_NO, K414, }, \
|
||||
{ K500, KC_NO, K502, K503, K504, K505, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, K511, K512, K513, K514, }, \
|
||||
{ K600, K601, K602, K603, K604, K605, K606, K607, KC_NO, K609, K610, K611, K612, K613, K614, }, \
|
||||
{ K700, K701, K702, K703, K704, K705, K706, KC_NO, K708, K709, K710, K711, K712, K713, K714 } \
|
||||
}
|
||||
|
||||
|
||||
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
Loading…
Reference in New Issue