Add support for JD40 MKII PCB

RGB Included.
example_keyboards
Major Koos 8 years ago
parent e28d151a8a
commit 295ef0d964

@ -0,0 +1,74 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
# CONSOLE_ENABLE ?= yes # Console for debug(+400)
# COMMAND_ENABLE ?= yes # Commands for debug and configuration
KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
# MIDI_ENABLE ?= YES # MIDI controls
# UNICODE_ENABLE ?= YES # Unicode
# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
RGBLIGHT_ENABLE ?= yes # Enable RGB Underglow
ifndef QUANTUM_DIR
include ../../Makefile
endif

@ -0,0 +1,79 @@
/*
Copyright 2012 Jun Wako <wakojun@gmail.com>
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0x6060
#define DEVICE_VER 0x0001
#define MANUFACTURER geekhack
#define PRODUCT jd40v2
#define DESCRIPTION t.m.k. keyboard firmware for JD40 MKII
/* key matrix size */
#define MATRIX_ROWS 4
#define MATRIX_COLS 12
/*
* Keyboard Matrix Assignments
*
* Change this to how you wired your keyboard
* COLS: AVR pins used for columns, left to right
* ROWS: AVR pins used for rows, top to bottom
* DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
* ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
*
*/
#define MATRIX_ROW_PINS { F0, F1, F5, B4 }
#define MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 }
#define UNUSED_PINS
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION COL2ROW
/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
#define DEBOUNCING_DELAY 5
/* define if matrix has ghost (lacks anti-ghosting diodes) */
//#define MATRIX_HAS_GHOST
/* number of backlight levels */
#define BACKLIGHT_LEVELS 3
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
#define LOCKING_RESYNC_ENABLE
/* key combination for magic key command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
#define RGB_DI_PIN D3
#define RGBLIGHT_TIMER
#define RGBLED_NUM 12 // Number of LEDs
#define RGBLIGHT_HUE_STEP 8
#define RGBLIGHT_SAT_STEP 8
#define RGBLIGHT_VAL_STEP 8
#endif

@ -0,0 +1,26 @@
#include "jd40.h"
void led_set_kb(uint8_t usb_led) {
// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
// if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
// gh60_caps_led_on();
// } else {
// gh60_caps_led_off();
// }
// if (usb_led & (1<<USB_LED_NUM_LOCK)) {
// gh60_esc_led_on();
// } else {
// gh60_esc_led_off();
// }
// if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
// gh60_fn_led_on();
// } else {
// gh60_fn_led_off();
// }
led_set_user(usb_led);
}

@ -0,0 +1,45 @@
#ifndef JD40_H
#define JD40_H
#include "quantum.h"
#include "led.h"
/* GH60 LEDs
* GPIO pads
* 0 F7 WASD LEDs
* 1 F6 ESC LED
* 2 F5 FN LED
* 3 F4 POKER Arrow LEDs
* B2 Capslock LED
* B0 not connected
*/
/*
inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); }
inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); }
inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); }
inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); }
inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); }
inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); }
inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); }
inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); }
inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); }
inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); }
*/
/* JD40 MKII keymap definition macro
*/
#define KEYMAP( \
K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, \
K13, K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, \
K24, K25, K26, K27, K28, K29, K30, K31, K32, K33, K34, \
K35, K36, K37, K38, K39, K40, K41, K42, K43, K44 \
) { \
{ KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K10, KC_##K11, KC_##K12 }, \
{ KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_NO }, \
{ KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_NO }, \
{ KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_NO, KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_NO } \
}
#endif

@ -0,0 +1,164 @@
#include "jd40.h"
#include "action_layer.h"
#define _BL 0
#define _AL 1
#define _FL 2
#define _UL 3
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[_BL] = KEYMAP(
F12, Q, W, E, R, T, Y, U, I, O, P, BSPC,
TAB, A, S, D, F, G, H, J, K, L, ENT,
LSFT, Z, X, C, V, B, N, M, COMM, UP, DOT,
LCTL, LGUI, LALT, FN0, SPC, SPC, FN0, LEFT, DOWN, RIGHT ),
[_AL] = KEYMAP(
GRV, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, DEL,
CAPS, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0,
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, SCLN, PGUP, QUOT,
TRNS, TRNS, TRNS, TRNS, FN3, FN3, TRNS, HOME, PGDN, END ),
[_FL] = KEYMAP(
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ),
[_UL] = KEYMAP(
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
TRNS, FN4, FN5, FN11, FN10, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS,
TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ),
};
enum function_id {
RGBLED_TOGGLE,
RGBLED_STEP_MODE,
RGBLED_INCREASE_HUE,
RGBLED_DECREASE_HUE,
RGBLED_INCREASE_SAT,
RGBLED_DECREASE_SAT,
RGBLED_INCREASE_VAL,
RGBLED_DECREASE_VAL,
SHIFT_ESC,
};
const uint16_t PROGMEM fn_actions[] = {
[0] = ACTION_LAYER_MOMENTARY(1), // Momentary Fn overlay
[1] = ACTION_LAYER_TOGGLE(2), // Toggle Arrow Layer overlay
[2] = ACTION_LAYER_TAP_KEY(2, KC_CAPS), // Tap to toggle caps lock and hold to activate function layer
[3] = ACTION_LAYER_TOGGLE(3), // Toggle Underglow Layer overlay
[4] = ACTION_FUNCTION(RGBLED_TOGGLE), //Turn on/off underglow
[5] = ACTION_FUNCTION(RGBLED_STEP_MODE), // Change underglow mode
[6] = ACTION_FUNCTION(RGBLED_INCREASE_HUE),
[7] = ACTION_FUNCTION(RGBLED_DECREASE_HUE),
[8] = ACTION_FUNCTION(RGBLED_INCREASE_SAT),
[9] = ACTION_FUNCTION(RGBLED_DECREASE_SAT),
[10] = ACTION_FUNCTION(RGBLED_INCREASE_VAL),
[11] = ACTION_FUNCTION(RGBLED_DECREASE_VAL),
[12] = ACTION_FUNCTION(SHIFT_ESC),
};
const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
{
// MACRODOWN only works in this function
switch(id) {
case 0:
if (record->event.pressed) {
register_code(KC_RSFT);
} else {
unregister_code(KC_RSFT);
}
break;
}
return MACRO_NONE;
};
void matrix_scan_user(void) {
// Layer LED indicators
// ESC led on when in function layer, WASD cluster leds enabled when on arrow cluster
uint32_t layer = layer_state;
if (layer & (1<<1)) {
//gh60_wasd_leds_on();
} else {
//gh60_wasd_leds_off();
}
if (layer & (1<<2)) {
//gh60_esc_led_on();
} else {
//gh60_esc_led_off();
}
};
#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT))
void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) {
switch (id) {
case RGBLED_TOGGLE:
//led operations
if (record->event.pressed) {
rgblight_toggle();
}
break;
case RGBLED_INCREASE_HUE:
if (record->event.pressed) {
rgblight_increase_hue();
}
break;
case RGBLED_DECREASE_HUE:
if (record->event.pressed) {
rgblight_decrease_hue();
}
break;
case RGBLED_INCREASE_SAT:
if (record->event.pressed) {
rgblight_increase_sat();
}
break;
case RGBLED_DECREASE_SAT:
if (record->event.pressed) {
rgblight_decrease_sat();
}
break;
case RGBLED_INCREASE_VAL:
if (record->event.pressed) {
rgblight_increase_val();
}
break;
case RGBLED_DECREASE_VAL:
if (record->event.pressed) {
rgblight_decrease_val();
}
break;
case RGBLED_STEP_MODE:
if (record->event.pressed) {
rgblight_step();
}
break;
static uint8_t shift_esc_shift_mask;
// Shift + ESC = ~
case SHIFT_ESC:
shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK;
if (record->event.pressed) {
if (shift_esc_shift_mask) {
add_key(KC_GRV);
send_keyboard_report();
} else {
add_key(KC_ESC);
send_keyboard_report();
}
} else {
if (shift_esc_shift_mask) {
del_key(KC_GRV);
send_keyboard_report();
} else {
del_key(KC_ESC);
send_keyboard_report();
}
}
break;
}
};

@ -0,0 +1,17 @@
## jd40 mkii keyboard firmware
Pins:
MATRIX_ROW_PINS { F0, F1, F5, B4 }
MATRIX_COL_PINS { F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2 }
RGB_DI_PIN D3
======================
## Quantum MK Firmware
For the full Quantum feature list, see [the parent readme.md](/readme.md).
## Building
Download or clone the whole firmware and navigate to the keyboards/jd40 folder.
Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Amtel Flip to program your .hex file.
Loading…
Cancel
Save