Add support for rev3 of the Atom47 (#2672)

* Added support for rev3 of the Atom47

* Updated Atom47 readme's

* Fix redefine error on rev2 and add maartenwut's keymap

* Fix redefine error on LEdiodes keymap
keycode_versioning 0.6.4
Maarten Dekkers 7 years ago committed by Jack Humbert
parent 7bbc9ccc31
commit d777a05864

@ -16,16 +16,9 @@ void matrix_scan_kb(void) {
void led_init_ports(void) {
// * Set our LED pins as output
DDRB &= ~(1<<5);
DDRE |= (1 << 6);
}
void led_set_kb(uint8_t usb_led) {
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
// Turn capslock on
PORTF |= (1<<5);
} else {
// Turn capslock off
PORTF &= ~(1<<5);
}
led_set_user(usb_led);
led_set_user(usb_led);
}

@ -9,14 +9,14 @@
#define KEYMAP_ANSI( \
k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, \
k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1c, \
k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2c, \
k30, k31, k32, k33, k34, k36, k38, k39, k3a, k3c \
k20, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c, \
k30, k31, k32, k33, k35, k37, k39, k3a, k3b, k3c \
) \
{ \
{k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c}, \
{k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, XXX, k1c}, \
{k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, XXX, k2c}, \
{k30, k31, k32, k33, k34, XXX, k36, XXX, k38, k39, k3a, XXX, k3c} \
{k20, XXX, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, k2c}, \
{k30, k31, k32, k33, XXX, k35, XXX, k37, XXX, k39, k3a, k3b, k3c} \
}
void matrix_init_user(void);

@ -34,8 +34,8 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
// ROWS: Top to bottom, COLS: Left to right
#define MATRIX_ROW_PINS {B1,B2,B3,B7}
#define MATRIX_COL_PINS {D7,D5,F0,F1,F4,F6,F7,D4,C7,C6,D6,B5,B4}
#define MATRIX_ROW_PINS {B3,B2,B1,B0}
#define MATRIX_COL_PINS {B7,F0,F1,F4,F6,D4,D6,D7,B4,B5,C6,C7,F7}
#define UNUSED_PINS
#define BACKLIGHT_PIN B6
@ -49,10 +49,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
/* Set 0 if debouncing isn't needed */
#define DEBOUNCING_DELAY 5
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
#define LOCKING_RESYNC_ENABLE
/* key combination for command */
#define IS_COMMAND() ( \
@ -63,11 +59,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#define BACKLIGHT_LEVELS 4
#endif
#define RGB_DI_PIN F5 // The pin the LED strip is connected to
#define RGBLED_NUM 6 // Number of LEDs in your strip
#define RGB_DI_PIN D0 // The pin the LED strip is connected to
#define RGBLED_NUM 1 // Number of LEDs in your strip
#define QMK_ESC_OUTPUT B7 // usually COL
#define QMK_ESC_INPUT B3 // usually ROW
#define QMK_LED E6
#define QMK_ESC_OUTPUT D7 // usually COL
#define QMK_ESC_INPUT B1 // usually ROW
#define QMK_LED B6
#endif

@ -1,4 +1,4 @@
#include QMK_KEYBOARD_H
#include "atom47.h"
// Each layer gets a name for readability, which is then used in the keymap matrix below.
// The underscores don't mean anything - you can have a layer called STUFF or any other name.
@ -16,24 +16,37 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[_MA] = KEYMAP_ANSI(
KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \
KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_FN1), \
KC_LCTL, KC_LGUI, KC_LALT, MO(_PN), KC_SPC, KC_SPC, MO(_FN), KC_RALT, KC_APP, KC_RCTRL), \
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_FN1), \
KC_LCTL, KC_LGUI, KC_LALT, MO(_PN), KC_SPC, KC_SPC, MO(_FN), KC_RALT, KC_APP, KC_RCTRL), \
[_FN] = KEYMAP_ANSI(
_______, KC_VOLD, KC_VOLU, KC_MUTE, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, \
KC_CAPS, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_INS, _______, \
_______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
_______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
[_FN1] = KEYMAP_ANSI(
KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
_______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
_______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
[_PN] = KEYMAP_ANSI(
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, RESET),
};
RGB_TOG, RGB_HUI, RGB_SAI, RGB_VAI, _______, _______, _______, _______, _______, _______, _______, _______, \
RGB_MOD, RGB_HUD, RGB_SAD, RGB_VAD, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, RESET),
};
void led_set_user(uint8_t usb_led) {
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
// Turn capslock on
PORTE &= ~(1 << 6);
} else {
// Turn capslock off
PORTE |= (1 << 6);
}
}

@ -1,10 +1 @@
To be updated...
// This layer is just a blank template to be copied for easy layer creation. please don not edit it.
[_LX] = KEYMAP_ANSI(
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, RESET),
This is the default keymap as found on the Vortex Core, with some added buttons for RGB and backlight control.

@ -0,0 +1,46 @@
#include "atom47.h"
// Each layer gets a name for readability, which is then used in the keymap matrix below.
// The underscores don't mean anything - you can have a layer called STUFF or any other name.
// Layer names don't all need to be of the same length, obviously, and you can also skip them
// entirely and just use numbers.
#define _MA 0 //Main layer
#define _LO 1 //FN1
#define _RA 2 //FN
#define _______ KC_TRNS
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[_MA] = KEYMAP_ANSI(
KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \
KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, \
KC_LCTL, KC_LGUI, KC_LALT, MO(_LO), KC_SPC, KC_SPC, MO(_RA), KC_RALT, KC_APP, KC_RCTRL), \
[_RA] = KEYMAP_ANSI(
_______, _______, _______, _______, _______, _______, _______, KC_PGUP, KC_UP, KC_PGDN, _______, _______, _______, \
KC_CAPS, _______, _______, _______, _______, _______, _______, KC_LEFT, KC_DOWN, KC_RIGHT, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, KC_VOLD, KC_VOLU, KC_MPLY, KC_PSCR, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
[_LO] = KEYMAP_ANSI(
KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
_______, _______, _______, _______, _______, _______, _______, KC_QUOT, KC_LBRC, KC_RBRC, KC_BSLS, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, RESET), \
};
void led_set_user(uint8_t usb_led) {
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
// Turn capslock on
PORTE &= ~(1 << 6);
} else {
// Turn capslock off
PORTE |= (1 << 6);
}
}

@ -0,0 +1 @@
This is the default keymap as found on the Vortex Core, with some added buttons for RGB and backlight control.

@ -1,28 +1,26 @@
# ATOM47
# Atom47
![ATOM47](https://i.imgur.com/rjrFTKT.png)
![Atom47](https://i.imgur.com/Wwflqvt.png)
## Support
Keyboard Maintainer: [Matthew Kerfoot(https://github.com/mkerfoot)
Hardware Supported: ATOM47
Keyboard Maintainer: [Maarten Dekkers(https://github.com/maartenwut)
Hardware Supported: Atom47 rev3
Hardware Availability: [GeekHack.com Group Buy](https://geekhack.org/index.php?topic=93447.msg2545221)
## Features
QMK Firmware
6 Underglow RGB leds
In-switch leds
Through-hole micro usb connector (less likely to break off!)
South facing leds for the QMX/Zealencio users
Multiple layouts
Easily reachable reset button under the spacebar
CapsLock indicator
- QMK Firmware
- 6 Underglow RGB leds
- In-switch leds
- Through-hole micro usb connector (less likely to break off!)
- South facing leds for the QMX/Zealencio users
- Multiple layouts
- Easily reachable reset button under the spacebar
- CapsLock indicator
## Build
To build the default keymap, simply run `make atom47:default`.
For an alternative, heavily modified layout you would just need to run `make atom47:LEdiodes`.
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.
![ATOM47](https://i.imgur.com/WebeUOF.png)
![Atom47](https://i.imgur.com/JfYnOba.jpg)

@ -63,11 +63,11 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#define BACKLIGHT_LEVELS 4
#endif
#define RGB_DI_PIN D0 // The pin the LED strip is connected to
#define RGBLED_NUM 1 // Number of LEDs in your strip
#define QMK_ESC_OUTPUT D7 // usually COL
#define QMK_ESC_INPUT B1 // usually ROW
#define QMK_LED B6
#define QMK_LED B6
#endif

@ -0,0 +1,31 @@
#include "atom47.h"
#include "led.h"
void matrix_init_kb(void) {
// put your keyboard start-up code here
// runs once when the firmware starts up
matrix_init_user();
led_init_ports();
};
void matrix_scan_kb(void) {
// put your looping keyboard code here
// runs every cycle (a lot)
matrix_scan_user();
};
void led_init_ports(void) {
// * Set our LED pins as output
DDRB &= ~(1<<5);
}
void led_set_kb(uint8_t usb_led) {
if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
// Turn capslock on
PORTF |= (1<<5);
} else {
// Turn capslock off
PORTF &= ~(1<<5);
}
led_set_user(usb_led);
}

@ -0,0 +1,25 @@
#ifndef ATOM47_H
#define ATOM47_H
#include "quantum.h"
// readability
#define XXX KC_NO
#define KEYMAP_ANSI( \
k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, \
k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1c, \
k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2c, \
k30, k31, k32, k33, k34, k36, k38, k39, k3a, k3c \
) \
{ \
{k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c}, \
{k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, XXX, k1c}, \
{k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, XXX, k2c}, \
{k30, k31, k32, k33, k34, XXX, k36, XXX, k38, k39, k3a, XXX, k3c} \
}
void matrix_init_user(void);
void matrix_scan_user(void);
#endif

@ -0,0 +1,74 @@
/*
Copyright 2012 Maarten Dekkers <atomkeeb@gmail.com
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xFEED
#define PRODUCT_ID 0x6060
#define DEVICE_VER 0x0003
#define MANUFACTURER Vortex
#define PRODUCT Core
#define DESCRIPTION Atom47 PCB for the Vortex Core
/* key matrix size */
#define MATRIX_ROWS 4
#define MATRIX_COLS 13
// ROWS: Top to bottom, COLS: Left to right
#define MATRIX_ROW_PINS {B1,B2,B3,B7}
#define MATRIX_COL_PINS {D7,D5,F0,F1,F4,F6,F7,D4,C7,C6,D6,B5,B4}
#define UNUSED_PINS
#define BACKLIGHT_PIN B6
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION COL2ROW
/* define if matrix has ghost */
//#define MATRIX_HAS_GHOST
/* Set 0 if debouncing isn't needed */
#define DEBOUNCING_DELAY 5
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
#define LOCKING_RESYNC_ENABLE
/* key combination for command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
/* Backlight configuration
*/
#define BACKLIGHT_LEVELS 4
#define RGB_DI_PIN D0 // The pin the LED strip is connected to
#define RGBLED_NUM 1 // Number of LEDs in your strip
#define QMK_ESC_OUTPUT D7 // usually COL
#define QMK_ESC_INPUT B1 // usually ROW
#define QMK_LED B6
#endif

@ -1,4 +1,4 @@
#include QMK_KEYBOARD_H
#include "atom47.h"
// These are all aliases for the function layers.
#define _L0 0

@ -0,0 +1,39 @@
#include "atom47.h"
// Each layer gets a name for readability, which is then used in the keymap matrix below.
// The underscores don't mean anything - you can have a layer called STUFF or any other name.
// Layer names don't all need to be of the same length, obviously, and you can also skip them
// entirely and just use numbers.
#define _MA 0 //Main layer
#define _FN 1 //Fn
#define _FN1 2 //Fn1
#define _PN 3 //Pn
#define _______ KC_TRNS
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[_MA] = KEYMAP_ANSI(
KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \
KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \
KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_FN1), \
KC_LCTL, KC_LGUI, KC_LALT, MO(_PN), KC_SPC, KC_SPC, MO(_FN), KC_RALT, KC_APP, KC_RCTRL), \
[_FN] = KEYMAP_ANSI(
_______, KC_VOLD, KC_VOLU, KC_MUTE, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, \
KC_CAPS, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_INS, _______, \
_______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
[_FN1] = KEYMAP_ANSI(
KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \
KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \
_______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \
[_PN] = KEYMAP_ANSI(
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \
_______, _______, _______, _______, _______, _______, _______, _______, _______, RESET),
};

@ -0,0 +1 @@
This is the default keymap as found on the Vortex Core, with some added buttons for backlight control.

@ -0,0 +1,23 @@
# Atom47 rev2
This is the keymap for rev2 of the Atom47. Only 9 of those have been sold for testing purposes. It had a slightly misaligned usb port and the pcb was too thick (should've been 1.2mm instead of 1.6mm). The pcb only supports the default hardware layout, although /u/ChrisSwires has [modified his](https://www.reddit.com/r/MechanicalKeyboards/comments/7n2dua/not_your_average_core_with_honeywell/) and put a big spacebar in it.
## Support
Keyboard Maintainer: [Matthew Kerfoot(https://github.com/mkerfoot)
Hardware Supported: Atom47 rev2
Hardware Availability: None
## Features
- QMK Firmware
- In-switch leds
- Through-hole micro usb connector (less likely to break off!)
- Easily reachable reset button under the spacebar
- In-switch CapsLock indicator
## Build
To build the default keymap, simply run `make atom47/rev2:default`.
For an alternative, heavily modified layout you would just need to run `make atom47/rev2:LEdiodes`.
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

@ -0,0 +1,65 @@
# MCU name
#MCU = at90usb1287
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870)
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality (+1150)
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID

@ -56,8 +56,8 @@ MOUSEKEY_ENABLE = no # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870)
NKRO_ENABLE = no # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
RGBLIGHT_ENABLE = yes # Enable keyboard underlight functionality (+4870)
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality (+1150)
MIDI_ENABLE = no # MIDI controls
AUDIO_ENABLE = no

Loading…
Cancel
Save