Add Chocopad keyboard

planck_rev6
Danny Nguyen 7 years ago committed by Jack Humbert
parent c73514a2b7
commit 9a91b42e92

@ -0,0 +1,14 @@
Chocopad
========
A 4x4 macropad keyboard using Kailh PG1350 Lower Profile Choc switches.
Keyboard Maintainer: Keebio
Hardware Supported: Chocopad PCB, Arduino Pro Micro
Hardware Availability: [Keebio](https://keeb.io)
Make example for this keyboard (after setting up your build environment):
make chocopad:default
See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information.

@ -0,0 +1 @@
#include "chocopad.h"

@ -0,0 +1,32 @@
#ifndef CHOCOPAD_H
#define CHOCOPAD_H
#include "quantum.h"
#define KEYMAP( \
A1, A2, A3, A4, \
B1, B2, B3, B4, \
C1, C2, C3, C4, \
D1, D2, D3, D4 \
) { \
{ A1, A2, A3, A4 }, \
{ B1, B2, B3, B4 }, \
{ C1, C2, C3, C4 }, \
{ D1, D2, D3, D4 } \
}
// Used to create a keymap using only KC_ prefixed keys
#define KC_KEYMAP( \
A1, A2, A3, A4, \
B1, B2, B3, B4, \
C1, C2, C3, C4, \
D1, D2, D3, D4 \
) \
KEYMAP( \
KC_##A1, KC_##A2, KC_##A3, KC_##A4, \
KC_##B1, KC_##B2, KC_##B3, KC_##B4, \
KC_##C1, KC_##C2, KC_##C3, KC_##C4, \
KC_##D1, KC_##D2, KC_##D3, KC_##D4 \
)
#endif

@ -0,0 +1,59 @@
#ifndef CONFIG_H
#define CONFIG_H
#include "config_common.h"
/* USB Device descriptor parameter */
#define VENDOR_ID 0xCEEB
#define PRODUCT_ID 0x1144
#define DEVICE_VER 0x0100
#define MANUFACTURER Keebio
#define PRODUCT Chocopad
#define DESCRIPTION 4x4 macropad using Kailh Choc low-profile switches
/* key matrix size */
#define MATRIX_ROWS 4
#define MATRIX_COLS 4
/* key matrix pins */
#define MATRIX_ROW_PINS { D7, E6, B3, B2 }
#define MATRIX_COL_PINS { D2, D4, F6, F5 }
/* COL2ROW or ROW2COL */
#define DIODE_DIRECTION COL2ROW
/* number of backlight levels */
#define BACKLIGHT_PIN B5
#define BACKLIGHT_LEVELS 6
/* Set 0 if debouncing isn't needed */
#define DEBOUNCING_DELAY 5
/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
#define LOCKING_SUPPORT_ENABLE
/* Locking resynchronize hack */
#define LOCKING_RESYNC_ENABLE
/* key combination for command */
#define IS_COMMAND() ( \
keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
)
/* prevent stuck modifiers */
#define PREVENT_STUCK_MODIFIERS
#ifdef RGB_DI_PIN
#define RGBLIGHT_ANIMATIONS
#define RGBLIGHT_HUE_STEP 8
#define RGBLIGHT_SAT_STEP 8
#define RGBLIGHT_VAL_STEP 8
#endif
#define RGB_DI_PIN D3
#define RGBLIGHT_TIMER
#define RGBLED_NUM 4
#define ws2812_PORTREG PORTD
#define ws2812_DDRREG DDRD
#endif

@ -0,0 +1,6 @@
#ifndef CONFIG_USER_H
#define CONFIG_USER_H
#include "../../config.h"
#endif

@ -0,0 +1,61 @@
#include "chocopad.h"
#define _BASE 0
#define _FN1 1
#define _FN2 2
#define KC_ KC_TRNS
#define _______ KC_TRNS
#define KC_X1 MO(_FN1)
#define KC_X2 MO(_FN2)
#define KC_RST RESET
#define KC_BSTP BL_STEP
#define KC_RTOG RGB_TOG
#define KC_RMOD RGB_MOD
#define KC_RHUI RGB_HUI
#define KC_RHUD RGB_HUD
#define KC_RSAI RGB_SAI
#define KC_RSAD RGB_SAD
#define KC_RVAI RGB_VAI
#define KC_RVAD RGB_VAD
const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
[_BASE] = KC_KEYMAP(
//,----+----+----+----.
PGUP,HOME, UP ,END ,
//|----+----+----+----|
PGDN,LEFT,DOWN,RGHT,
//|----+----+----+----|
X2 ,VOLU,MPLY,MPRV,
//|----+----+----+----|
X1 ,VOLD,MUTE,MNXT
//`----+----+----+----'
),
[_FN1] = KC_KEYMAP(
//,----+----+----+----.
ESC , P7 , P8 , P9 ,
//|----+----+----+----|
TAB , P4 , P5 , P6 ,
//|----+----+----+----|
ENT , P1 , P2 , P3 ,
//|----+----+----+----|
, P0 , P0 ,DOT
//`----+----+----+----'
),
[_FN2] = KC_KEYMAP(
//,----+----+----+----.
RTOG,RHUI,RSAI,RVAI,
//|----+----+----+----|
RMOD,RHUD,RSAD,RVAD,
//|----+----+----+----|
, , ,RST ,
//|----+----+----+----|
BSTP, , ,
//`----+----+----+----'
)
};

@ -0,0 +1,5 @@
RGBLIGHT_ENABLE = yes
ifndef QUANTUM_DIR
include ../../../../Makefile
endif

@ -0,0 +1,56 @@
# MCU name
MCU = atmega32u4
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 16000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
# Boot Section Size in *bytes*
OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# comment out to disable the options.
#
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = no # Console for debug(+400)
COMMAND_ENABLE = no # Commands for debug and configuration
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
AUDIO_ENABLE = no
RGBLIGHT_ENABLE = yes
Loading…
Cancel
Save